What is enthalpy?
Show answer & solution
Answer: (A) H = U + PV, the sum of internal energy and flow work
Enthalpy changes give heat transferred at constant pressure.
Chemical Engineering · Stoichiometry
30 questions, each with the answer and a worked solution.
Practice interactively and track your score →What is enthalpy?
Answer: (A) H = U + PV, the sum of internal energy and flow work
Enthalpy changes give heat transferred at constant pressure.
What is the relation between Cp and Cv for an ideal gas?
Answer: (B) Cp − Cv = R
γ = Cp/Cv is about 1.67 for monatomic and 1.4 for diatomic gases.
What is the ratio of specific heats γ for a diatomic gas such as air?
Answer: (B) About 1.4
It is about 1.3 for triatomic gases.
What does Kopp's rule state?
Answer: (A) The heat capacity of a solid compound is approximately the sum of the heat capacities of its constituent elements
It is used when data are not available.
What does the law of Dulong and Petit state?
Answer: (D) The molar heat capacity of most solid elements is about 26 J/(mol·K) (about 6.4 cal/(mol·K))
It applies at ordinary and high temperatures.
How much heat is needed to raise 10 kg of water from 20 °C to 80 °C (Cp = 4.18 kJ/(kg·K))?
Answer: (C) About 2,508 kJ
Q = 10 × 4.18 × 60.
What is the approximate latent heat of vaporisation of water at 100 °C?
Answer: (C) About 2,257 kJ/kg
The latent heat of fusion of ice is about 334 kJ/kg.
What is the standard heat of formation of an element in its standard state?
Answer: (B) Zero
Standard state is usually 25 °C and 1 atm.
What does Hess's law state?
Answer: (D) The heat of a reaction is the same whether it occurs in one step or several steps
It allows heats of reaction to be calculated from known reactions.
How is the standard heat of reaction calculated from heats of formation?
Answer: (A) Sum of heats of formation of products minus sum of heats of formation of reactants
Each term is multiplied by its stoichiometric coefficient.
What sign does the heat of reaction have for an exothermic reaction?
Answer: (D) Negative
Heat is released to the surroundings.
What is the difference between the higher (gross) and lower (net) calorific values of a fuel?
Answer: (A) The latent heat of the water vapour formed during combustion
HCV assumes water is condensed to liquid.
Which factors does the heat of solution depend on?
Answer: (B) The nature of the solute and solvent and the concentration of the solution
Integral heats of solution vary with concentration.
What is the approximate heat of neutralisation of a strong acid by a strong base?
Answer: (B) About −57 kJ per mole of water formed
It is nearly constant because the net reaction is H⁺ + OH⁻ → H₂O.
What is the heat of complete wetting?
Answer: (D) The enthalpy change when a unit mass of solid is wetted with so much liquid that further addition gives no thermal effect
It is important in drying and adsorption.
What is the adiabatic flame temperature?
Answer: (A) The maximum temperature reached when a fuel burns completely with no heat loss
Excess air lowers the adiabatic flame temperature.
How does excess air affect the adiabatic flame temperature?
Answer: (D) It lowers the flame temperature
Extra air absorbs heat without contributing to combustion.
Which equation gives the effect of temperature on the heat of reaction?
Answer: (B) Kirchhoff's equation
d(ΔH)/dT = ΔCp.
What does a Mollier diagram plot?
Answer: (A) Enthalpy against entropy
It is widely used for steam calculations.
How much heat is needed to convert 1 kg of water at 100 °C to steam at 100 °C?
Answer: (D) About 2,257 kJ
Only latent heat is needed at constant temperature.
What is the heat of hydration?
Answer: (C) The heat released or absorbed when an anhydrous salt combines with water to form a hydrate
For example, CuSO₄ + 5H₂O → CuSO₄·5H₂O.
What is an enthalpy–concentration diagram used for?
Answer: (B) Energy balance calculations for mixing, evaporation and distillation of solutions
Common examples are NaOH–water and ammonia–water diagrams.
What is the general energy balance for a steady-flow process neglecting kinetic and potential energy?
Answer: (A) Q − W = ΔH
Kinetic and potential terms are often small in process units.
What is sensible heat?
Answer: (C) Heat that changes the temperature of a substance without a phase change
Latent heat is absorbed at constant temperature.
What is the molar heat capacity at constant pressure of a monatomic ideal gas?
Answer: (B) (5/2)R
Cv = (3/2)R for monatomic gases.
What is the standard heat of combustion of a substance?
Answer: (D) The enthalpy change when one mole of it burns completely in oxygen at standard conditions
Heats of combustion are used to find heats of formation of organic compounds.
How much heat is needed to melt 5 kg of ice at 0 °C (latent heat of fusion 334 kJ/kg)?
Answer: (C) 1,670 kJ
Q = 5 × 334.
What is an endothermic reaction?
Answer: (B) A reaction that absorbs heat from the surroundings
ΔH is positive for endothermic reactions.
Which process takes place at constant enthalpy?
Answer: (A) Throttling through a valve
The Joule–Thomson expansion is isenthalpic.
What is the mean heat capacity used for over a temperature range?
Answer: (B) To calculate sensible heat as mean Cp multiplied by temperature change
Mean Cp values are tabulated from a reference of 25 °C.