Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Environmental Engineering: Water Quality and Treatment

Chemical Engineering · Environmental Engineering

44 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

What does turbidity of water indicate?

  1. The pH
  2. The hardness
  3. The dissolved salt content
  4. The cloudiness caused by suspended particles that scatter light
Show answer & solution

Answer: (D) The cloudiness caused by suspended particles that scatter light

It is measured in nephelometric turbidity units (NTU).

Question 2

What is the WHO guideline value for arsenic in drinking water?

  1. 1 mg/L
  2. 10 µg/L
  3. 50 mg/L
  4. 100 µg/L
Show answer & solution

Answer: (B) 10 µg/L

Groundwater arsenic is a serious problem in parts of Punjab and Sindh.

Question 3

What is the WHO guideline value for fluoride in drinking water?

  1. 0.01 mg/L
  2. 1.5 mg/L
  3. 15 mg/L
  4. 50 mg/L
Show answer & solution

Answer: (B) 1.5 mg/L

Excess fluoride causes dental and skeletal fluorosis.

Question 4

What is the WHO guideline value for nitrate (as NO₃⁻) in drinking water?

  1. 0.5 mg/L
  2. 5 mg/L
  3. 50 mg/L
  4. 500 mg/L
Show answer & solution

Answer: (C) 50 mg/L

High nitrate causes methaemoglobinaemia (blue baby syndrome).

Question 5

What causes temporary hardness of water?

  1. Calcium and magnesium bicarbonates, removable by boiling
  2. Magnesium chloride only
  3. Sodium chloride
  4. Calcium sulphate
Show answer & solution

Answer: (A) Calcium and magnesium bicarbonates, removable by boiling

Permanent hardness is due to sulphates and chlorides.

Question 6

In what units is water hardness usually expressed?

  1. mg/L as NaCl
  2. NTU
  3. mg/L as CaCO₃
  4. pH units
Show answer & solution

Answer: (C) mg/L as CaCO₃

Water above about 180 mg/L as CaCO₃ is considered very hard.

Question 7

What is the lime–soda process?

  1. Reverse osmosis
  2. Disinfection with chlorine
  3. Filtration through sand
  4. Softening water by adding lime and soda ash to precipitate calcium carbonate and magnesium hydroxide
Show answer & solution

Answer: (D) Softening water by adding lime and soda ash to precipitate calcium carbonate and magnesium hydroxide

It removes both temporary and permanent hardness.

Question 8

What is the typical sequence of conventional surface water treatment?

  1. Screening, coagulation, flocculation, sedimentation, filtration and disinfection
  2. Disinfection, screening and boiling
  3. Reverse osmosis then coagulation
  4. Filtration only
Show answer & solution

Answer: (A) Screening, coagulation, flocculation, sedimentation, filtration and disinfection

Raw water from canals and rivers is treated this way.

Question 9

Which chemical is most commonly used as a coagulant in water treatment?

  1. Calcium carbonate
  2. Aluminium sulphate (alum)
  3. Sodium chloride
  4. Activated carbon
Show answer & solution

Answer: (B) Aluminium sulphate (alum)

Ferric chloride and polyaluminium chloride are alternatives.

Question 10

What is the purpose of flocculation?

  1. Gentle mixing that brings destabilised particles together to form larger flocs
  2. Removing salts
  3. Killing bacteria
  4. Rapid mixing to disperse chemicals
Show answer & solution

Answer: (A) Gentle mixing that brings destabilised particles together to form larger flocs

Flocs settle in the sedimentation basin.

Question 11

What is a jar test used for?

  1. Measuring BOD
  2. Measuring hardness
  3. Finding the optimum coagulant dose for a raw water
  4. Measuring chlorine residual
Show answer & solution

Answer: (C) Finding the optimum coagulant dose for a raw water

Doses are tested in a set of beakers with stirring.

Question 12

What is the difference between slow sand and rapid sand filters?

  1. They are identical
  2. Slow filters need backwashing every hour
  3. Rapid filters have no sand
  4. Slow sand filters rely on a biological layer at low rates; rapid filters work at much higher rates after coagulation and need backwashing
Show answer & solution

Answer: (D) Slow sand filters rely on a biological layer at low rates; rapid filters work at much higher rates after coagulation and need backwashing

Slow sand filters suit small communities.

Question 13

Why are rapid sand filters backwashed?

  1. To remove trapped solids and restore filtration capacity
  2. To soften the water
  3. To add chlorine
  4. To heat the water
Show answer & solution

Answer: (A) To remove trapped solids and restore filtration capacity

Backwashing expands the bed with upward flow.

Question 14

What is the main purpose of chlorination of drinking water?

  1. Removing turbidity
  2. Removing hardness
  3. Disinfection by killing pathogenic microorganisms
  4. Adding taste
Show answer & solution

Answer: (C) Disinfection by killing pathogenic microorganisms

A residual chlorine protects water in the distribution network.

Question 15

What is breakpoint chlorination?

  1. Adding chlorine only to wastewater
  2. Adding chlorine until all ammonia and reducing substances are oxidised so that free chlorine residual appears
  3. Stopping chlorination
  4. Adding a fixed dose regardless of demand
Show answer & solution

Answer: (B) Adding chlorine until all ammonia and reducing substances are oxidised so that free chlorine residual appears

Beyond the breakpoint, residual rises in proportion to dose.

Question 16

What is the typical free chlorine residual maintained in distribution systems?

  1. About 0.001 mg/L
  2. About 0.2–0.5 mg/L
  3. About 10 mg/L
  4. About 50 mg/L
Show answer & solution

Answer: (B) About 0.2–0.5 mg/L

Higher residuals cause taste complaints.

Question 17

What are disinfection by-products such as trihalomethanes formed from?

  1. Reaction of ozone with salt only
  2. Sand filters
  3. Bacteria
  4. Reaction of chlorine with natural organic matter in water
Show answer & solution

Answer: (D) Reaction of chlorine with natural organic matter in water

Removing organics before chlorination reduces them.

Question 18

Which disinfectant leaves no residual in the distribution system?

  1. Chlorine
  2. Chlorine dioxide
  3. Chloramine
  4. Ozone
Show answer & solution

Answer: (D) Ozone

Ozone is often followed by a small chlorine dose.

Question 19

How does ultraviolet (UV) disinfection work?

  1. It adds chemicals
  2. It heats the water
  3. UV light damages microbial DNA so that organisms cannot reproduce
  4. It filters bacteria
Show answer & solution

Answer: (C) UV light damages microbial DNA so that organisms cannot reproduce

It needs clear water to be effective.

Question 20

Which indicator organism group is used to test drinking water for faecal contamination?

  1. Coliform bacteria, especially E. coli
  2. Algae
  3. Viruses only
  4. Protozoa only
Show answer & solution

Answer: (A) Coliform bacteria, especially E. coli

E. coli must be absent in 100 mL of drinking water.

Question 21

What is total dissolved solids (TDS)?

  1. Hardness only
  2. Suspended particles
  3. Turbidity
  4. The total amount of dissolved inorganic and organic substances in water
Show answer & solution

Answer: (D) The total amount of dissolved inorganic and organic substances in water

Many Pakistani groundwaters have high TDS.

Question 22

Which treatment is most suitable for removing arsenic from groundwater for small communities?

  1. Coagulation–filtration with iron salts or adsorption on iron-based media
  2. Boiling
  3. Chlorination only
  4. Aeration only
Show answer & solution

Answer: (A) Coagulation–filtration with iron salts or adsorption on iron-based media

RO is effective but more costly.

Question 23

What is the main use of aeration in groundwater treatment?

  1. Removing fluoride
  2. Adding hardness
  3. Removing dissolved gases such as H₂S and CO₂ and oxidising iron and manganese
  4. Removing salts
Show answer & solution

Answer: (C) Removing dissolved gases such as H₂S and CO₂ and oxidising iron and manganese

Oxidised iron precipitates and is filtered.

Question 24

What is the per capita water demand often used for urban design in Pakistan?

  1. About 5 litres
  2. About 20 litres
  3. About 150–250 litres per person per day
  4. About 2,000 litres
Show answer & solution

Answer: (C) About 150–250 litres per person per day

Values depend on city size and standards.

Question 25

What is the main cause of waterborne diseases such as cholera and typhoid in cities?

  1. High pH
  2. Contamination of water supplies by sewage
  3. Hard water
  4. Fluoride
Show answer & solution

Answer: (B) Contamination of water supplies by sewage

Leaking pipes near sewers are a common cause.

Question 26

What does pH of water measure?

  1. The negative logarithm of hydrogen ion activity, indicating acidity or alkalinity
  2. The hardness
  3. The turbidity
  4. The salt content
Show answer & solution

Answer: (A) The negative logarithm of hydrogen ion activity, indicating acidity or alkalinity

Drinking water pH is usually 6.5–8.5.

Question 27

What is alkalinity of water?

  1. Its pH
  2. Its capacity to neutralise acids, mainly due to bicarbonate, carbonate and hydroxide
  3. Its hardness
  4. Its chloride content
Show answer & solution

Answer: (B) Its capacity to neutralise acids, mainly due to bicarbonate, carbonate and hydroxide

It buffers pH changes during coagulation.

Question 28

What is the process of desalination of seawater by reverse osmosis called?

  1. Slow sand filtration
  2. Lime softening
  3. Coagulation
  4. SWRO (seawater reverse osmosis)
Show answer & solution

Answer: (D) SWRO (seawater reverse osmosis)

Karachi and coastal industries use desalination plants.

Question 29

What is eutrophication?

  1. Excessive growth of algae and plants in water due to nutrient enrichment, especially nitrogen and phosphorus
  2. Drying of lakes
  3. Acidification of rain
  4. Salinity increase only
Show answer & solution

Answer: (A) Excessive growth of algae and plants in water due to nutrient enrichment, especially nitrogen and phosphorus

Algal decay depletes dissolved oxygen.

Question 30

What is the minimum dissolved oxygen generally needed to support most fish?

  1. About 0.1 mg/L
  2. About 50 mg/L
  3. About 4–5 mg/L
  4. Zero
Show answer & solution

Answer: (C) About 4–5 mg/L

Saturation in water is about 8–9 mg/L at 25 °C.

Question 31

What is the detention time typically used in sedimentation basins for water treatment?

  1. About 2 days
  2. About 2 minutes
  3. About 2–4 hours
  4. About 10 seconds
Show answer & solution

Answer: (C) About 2–4 hours

Surface overflow rate is also a key design parameter.

Question 32

What is the surface overflow rate of a settling tank?

  1. Flow rate divided by tank surface area
  2. Volume divided by time only
  3. Depth divided by area
  4. Flow rate times depth
Show answer & solution

Answer: (A) Flow rate divided by tank surface area

Particles with settling velocity above it are removed.

Question 33

What is the typical filtration rate of rapid sand filters?

  1. About 0.001 m³/(m²·h)
  2. About 0.1 m³/(m²·h)
  3. About 5–15 m³/(m²·h)
  4. About 100 m³/(m²·h)
Show answer & solution

Answer: (C) About 5–15 m³/(m²·h)

Slow sand filters work at about 0.1–0.2 m/h.

Question 34

What is the purpose of the Ct concept in disinfection?

  1. Measuring pH
  2. Expressing disinfection effectiveness as disinfectant concentration multiplied by contact time
  3. Measuring turbidity
  4. Measuring hardness
Show answer & solution

Answer: (B) Expressing disinfection effectiveness as disinfectant concentration multiplied by contact time

Required Ct depends on organism, temperature and pH.

Question 35

How does pH affect chlorine disinfection?

  1. Lower pH favours hypochlorous acid (HOCl), the stronger disinfectant
  2. Higher pH always improves disinfection
  3. pH has no effect
  4. Chlorine works only above pH 11
Show answer & solution

Answer: (A) Lower pH favours hypochlorous acid (HOCl), the stronger disinfectant

Above about pH 7.5 hypochlorite ion dominates.

Question 36

What is chloramination?

  1. UV treatment
  2. Disinfection using chlorine combined with ammonia to give a long-lasting residual
  3. Ozonation
  4. Chlorination at the breakpoint only
Show answer & solution

Answer: (B) Disinfection using chlorine combined with ammonia to give a long-lasting residual

Chloramines form fewer trihalomethanes.

Question 37

What is the main health effect of long-term arsenic exposure from drinking water?

  1. Rickets
  2. Tooth decay
  3. Goitre
  4. Skin lesions and cancers of skin, bladder and lungs
Show answer & solution

Answer: (D) Skin lesions and cancers of skin, bladder and lungs

Arsenicosis has been reported in parts of the Indus plain.

Question 38

What is iodine deficiency in some northern areas of Pakistan associated with?

  1. Fluorosis
  2. Blue baby syndrome
  3. Arsenicosis
  4. Goitre
Show answer & solution

Answer: (D) Goitre

Iodised salt programmes address it.

Question 39

Which process is used to remove iron and manganese from groundwater?

  1. Adding sugar
  2. Oxidation by aeration or chlorine followed by filtration
  3. Boiling
  4. Reverse osmosis only
Show answer & solution

Answer: (B) Oxidation by aeration or chlorine followed by filtration

Manganese needs stronger oxidants or higher pH.

Question 40

What is ion exchange softening?

  1. Replacing calcium and magnesium ions in water with sodium ions on a resin
  2. Adding hardness
  3. Disinfecting water
  4. Removing sodium
Show answer & solution

Answer: (A) Replacing calcium and magnesium ions in water with sodium ions on a resin

The resin is regenerated with brine.

Question 41

What is the main advantage of rainwater harvesting in water-scarce areas?

  1. It removes salts from seawater
  2. It increases floods
  3. It supplements water supply and recharges groundwater
  4. It purifies sewage
Show answer & solution

Answer: (C) It supplements water supply and recharges groundwater

It is promoted in Islamabad and arid regions.

Question 42

What is the main cause of falling groundwater levels in Lahore and other Punjab cities?

  1. Earthquakes
  2. Over-pumping beyond natural recharge
  3. Sea water intrusion only
  4. Excess rainfall
Show answer & solution

Answer: (B) Over-pumping beyond natural recharge

Managed recharge and metering are needed.

Question 43

What is waterlogging and salinity in irrigated land?

  1. Rising water tables and salt accumulation in soil due to seepage and poor drainage
  2. Desert formation by wind
  3. Snow melt
  4. Excess rainfall only
Show answer & solution

Answer: (A) Rising water tables and salt accumulation in soil due to seepage and poor drainage

SCARP tube wells were installed in Pakistan to address it.

Question 44

What is the threshold odour number (TON)?

  1. The odour intensity on a 10-point scale
  2. The pH
  3. The turbidity
  4. The dilution ratio at which odour is just detectable
Show answer & solution

Answer: (D) The dilution ratio at which odour is just detectable

It is used to assess taste and odour problems.

Practice these 44 questions interactively →