Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Environmental Engineering: Wastewater Treatment

Chemical Engineering · Environmental Engineering

46 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

What does BOD measure?

  1. Dissolved oxygen only
  2. The oxygen consumed by microorganisms in decomposing biodegradable organic matter
  3. Total organic carbon
  4. Oxygen consumed by chemical oxidation of all organics
Show answer & solution

Answer: (B) The oxygen consumed by microorganisms in decomposing biodegradable organic matter

The standard test is BOD₅ at 20 °C over 5 days.

Question 2

What does COD measure?

  1. Oxygen used by microbes only
  2. Dissolved oxygen
  3. Nitrogen content
  4. The oxygen equivalent of organic matter oxidised by a strong chemical oxidant such as dichromate
Show answer & solution

Answer: (D) The oxygen equivalent of organic matter oxidised by a strong chemical oxidant such as dichromate

COD is always at least as large as BOD.

Question 3

What does a high BOD/COD ratio (above about 0.5) indicate?

  1. The wastewater is readily biodegradable
  2. The wastewater is toxic
  3. It contains no organics
  4. It is drinking water
Show answer & solution

Answer: (A) The wastewater is readily biodegradable

Low ratios suggest non-biodegradable organics.

Question 4

What is the typical BOD₅ of raw domestic sewage?

  1. About 0.1 mg/L
  2. About 5 mg/L
  3. About 200–300 mg/L
  4. About 10,000 mg/L
Show answer & solution

Answer: (C) About 200–300 mg/L

Industrial wastes can be much stronger.

Question 5

What is the BOD₅ limit for industrial effluent discharged to inland waters under Pakistan's NEQS?

  1. 8 mg/L
  2. 80 mg/L
  3. 250 mg/L
  4. 800 mg/L
Show answer & solution

Answer: (B) 80 mg/L

The COD limit is 150 mg/L.

Question 6

What is the COD limit for industrial effluent discharged to inland waters under Pakistan's NEQS?

  1. 15 mg/L
  2. 150 mg/L
  3. 400 mg/L
  4. 1,500 mg/L
Show answer & solution

Answer: (B) 150 mg/L

Limits differ for discharge to sewers and the sea.

Question 7

What is the purpose of preliminary treatment of wastewater?

  1. Disinfection
  2. Removing dissolved organics
  3. Removing nutrients
  4. Removing large solids, grit and floating material with screens and grit chambers
Show answer & solution

Answer: (D) Removing large solids, grit and floating material with screens and grit chambers

It protects pumps and downstream units.

Question 8

What does primary treatment remove?

  1. Pathogens completely
  2. Dissolved salts
  3. Nitrogen
  4. Settleable solids and some BOD by sedimentation
Show answer & solution

Answer: (D) Settleable solids and some BOD by sedimentation

It removes about 50–70% of suspended solids and 25–40% of BOD.

Question 9

What is secondary (biological) treatment?

  1. Chlorination only
  2. Adding coagulants only
  3. Using microorganisms to remove dissolved and colloidal biodegradable organic matter
  4. Screening only
Show answer & solution

Answer: (C) Using microorganisms to remove dissolved and colloidal biodegradable organic matter

Activated sludge and trickling filters are examples.

Question 10

What is the activated sludge process?

  1. An aerated tank where microbial flocs degrade organics, followed by clarification and sludge recycle
  2. A screening process
  3. A sand filter
  4. An anaerobic pond only
Show answer & solution

Answer: (A) An aerated tank where microbial flocs degrade organics, followed by clarification and sludge recycle

Return activated sludge maintains the biomass.

Question 11

What is the F/M ratio in activated sludge?

  1. The food-to-microorganism ratio, kg BOD applied per kg MLVSS per day
  2. The filter to membrane ratio
  3. The fats to minerals ratio
  4. The flow to mass ratio
Show answer & solution

Answer: (A) The food-to-microorganism ratio, kg BOD applied per kg MLVSS per day

Conventional plants operate at about 0.2–0.5.

Question 12

What is MLSS?

  1. The sludge cake
  2. The final effluent solids
  3. Mixed liquor suspended solids, the concentration of biomass and solids in the aeration tank
  4. The influent solids
Show answer & solution

Answer: (C) Mixed liquor suspended solids, the concentration of biomass and solids in the aeration tank

Typical MLSS is 2,000–4,000 mg/L.

Question 13

What is sludge age (mean cell residence time)?

  1. The hydraulic retention time
  2. The digester volume
  3. The age of the plant
  4. The average time that microorganisms remain in the treatment system
Show answer & solution

Answer: (D) The average time that microorganisms remain in the treatment system

Longer sludge ages favour nitrification.

Question 14

What is the sludge volume index (SVI)?

  1. The sludge age
  2. The volume in mL occupied by 1 g of sludge after 30 minutes of settling
  3. The MLSS
  4. The BOD removal
Show answer & solution

Answer: (B) The volume in mL occupied by 1 g of sludge after 30 minutes of settling

SVI above about 150 mL/g indicates poor settling or bulking.

Question 15

What causes sludge bulking?

  1. Excessive growth of filamentous bacteria that settle poorly
  2. Too much grit
  3. Excess chlorine
  4. High pH only
Show answer & solution

Answer: (A) Excessive growth of filamentous bacteria that settle poorly

Low DO and low F/M can promote filaments.

Question 16

What is a trickling filter?

  1. An aeration tank
  2. A bed of media over which wastewater trickles and a biofilm degrades organic matter
  3. A chemical reactor
  4. A sand filter for drinking water
Show answer & solution

Answer: (B) A bed of media over which wastewater trickles and a biofilm degrades organic matter

It is an attached-growth process.

Question 17

What are waste stabilisation ponds?

  1. Chemical reactors
  2. Sand filters
  3. Deep tanks with mechanical aerators
  4. Shallow ponds using natural processes of bacteria and algae to treat wastewater
Show answer & solution

Answer: (D) Shallow ponds using natural processes of bacteria and algae to treat wastewater

They are low-cost and suit warm climates such as Pakistan.

Question 18

What is the role of algae in facultative ponds?

  1. Consuming oxygen
  2. Producing methane
  3. Producing oxygen by photosynthesis for aerobic bacteria
  4. Removing salts
Show answer & solution

Answer: (C) Producing oxygen by photosynthesis for aerobic bacteria

Bacteria provide CO₂ for algae.

Question 19

What is anaerobic treatment?

  1. Treatment by bacteria in the absence of oxygen, converting organics to methane and CO₂
  2. Filtration only
  3. Chemical oxidation
  4. Treatment with aeration
Show answer & solution

Answer: (A) Treatment by bacteria in the absence of oxygen, converting organics to methane and CO₂

It suits strong wastes such as distillery spent wash.

Question 20

What is a UASB reactor?

  1. A sand filter
  2. An upflow anaerobic sludge blanket reactor in which wastewater flows up through a granular sludge bed
  3. A cooling tower
  4. An aerobic tank
Show answer & solution

Answer: (B) An upflow anaerobic sludge blanket reactor in which wastewater flows up through a granular sludge bed

It produces biogas from high-strength wastewater.

Question 21

What is nitrification?

  1. Removal of BOD
  2. Conversion of nitrate to nitrogen gas
  3. Biological oxidation of ammonia to nitrite and then nitrate by autotrophic bacteria
  4. Removal of phosphorus
Show answer & solution

Answer: (C) Biological oxidation of ammonia to nitrite and then nitrate by autotrophic bacteria

Nitrosomonas and Nitrobacter carry it out.

Question 22

What is denitrification?

  1. Oxidation of ammonia
  2. Removal of solids
  3. Removal of phosphorus
  4. Biological reduction of nitrate to nitrogen gas under anoxic conditions
Show answer & solution

Answer: (D) Biological reduction of nitrate to nitrogen gas under anoxic conditions

An organic carbon source is needed.

Question 23

How is phosphorus commonly removed from wastewater?

  1. By chemical precipitation with alum, iron salts or lime, or by enhanced biological uptake
  2. By chlorination
  3. By screening
  4. By aeration only
Show answer & solution

Answer: (A) By chemical precipitation with alum, iron salts or lime, or by enhanced biological uptake

Phosphorus causes eutrophication.

Question 24

What is tertiary treatment?

  1. Sludge digestion
  2. Advanced treatment after secondary treatment to remove nutrients, residual solids or toxics
  3. Primary sedimentation
  4. Screening
Show answer & solution

Answer: (B) Advanced treatment after secondary treatment to remove nutrients, residual solids or toxics

Filtration and disinfection are common tertiary steps.

Question 25

What is the purpose of anaerobic sludge digestion?

  1. Heating the plant only
  2. Removing salts
  3. Producing drinking water
  4. Stabilising sludge, reducing its volume and pathogens, and producing biogas
Show answer & solution

Answer: (D) Stabilising sludge, reducing its volume and pathogens, and producing biogas

Mesophilic digesters operate near 35 °C.

Question 26

What is the typical composition of biogas from anaerobic digestion?

  1. About 50% oxygen
  2. About 60–70% methane and 30–40% CO₂
  3. About 90% nitrogen
  4. About 100% hydrogen
Show answer & solution

Answer: (B) About 60–70% methane and 30–40% CO₂

It can fuel boilers or engines.

Question 27

What is the main pollutant concern in tannery effluent?

  1. Radioactivity
  2. Fluoride only
  3. Chromium and high organic and salt loads
  4. Arsenic only
Show answer & solution

Answer: (C) Chromium and high organic and salt loads

Kasur and Sialkot tanneries generate such effluents.

Question 28

What is the main pollutant concern in textile dyeing effluent?

  1. Asbestos
  2. Radioactivity
  3. Mercury only
  4. Colour, high COD, pH and salts
Show answer & solution

Answer: (D) Colour, high COD, pH and salts

Pakistan's large textile sector makes this a major issue.

Question 29

What is a membrane bioreactor (MBR)?

  1. A cooling tower
  2. A sand filter
  3. Activated sludge combined with membrane filtration instead of a secondary clarifier
  4. An anaerobic pond
Show answer & solution

Answer: (C) Activated sludge combined with membrane filtration instead of a secondary clarifier

It gives high-quality effluent in a small footprint.

Question 30

What is a combined effluent treatment plant (CETP)?

  1. A shared treatment plant serving several industries in an industrial estate
  2. A water purification plant
  3. A sludge incinerator
  4. A plant treating only domestic sewage
Show answer & solution

Answer: (A) A shared treatment plant serving several industries in an industrial estate

It is cost-effective for small and medium industries.

Question 31

What is the hydraulic retention time (HRT) of a tank of 1,000 m³ receiving 250 m³/h?

  1. 0.25 h
  2. 1 h
  3. 4 h
  4. 250 h
Show answer & solution

Answer: (C) 4 h

HRT = V/Q.

Question 32

What is the typical design hydraulic retention time of conventional activated sludge aeration tanks?

  1. About 1 month
  2. About 4–8 hours
  3. About 5 minutes
  4. About 10 days
Show answer & solution

Answer: (B) About 4–8 hours

Extended aeration uses about 18–36 hours.

Question 33

What is extended aeration?

  1. An activated sludge variant with long aeration time and low F/M that produces less, more stable sludge
  2. A chemical process
  3. An anaerobic process
  4. A short-time process
Show answer & solution

Answer: (A) An activated sludge variant with long aeration time and low F/M that produces less, more stable sludge

It suits small communities and package plants.

Question 34

What is a sequencing batch reactor (SBR)?

  1. A sand filter
  2. An anaerobic pond
  3. A continuous trickling filter
  4. A fill-and-draw activated sludge system where aeration and settling occur in the same tank in sequence
Show answer & solution

Answer: (D) A fill-and-draw activated sludge system where aeration and settling occur in the same tank in sequence

It is compact and flexible.

Question 35

What is the oxygen requirement in activated sludge mainly used for?

  1. Mixing only
  2. Heating
  3. Oxidation of organic matter and nitrification
  4. Disinfection
Show answer & solution

Answer: (C) Oxidation of organic matter and nitrification

Diffused or surface aerators supply oxygen.

Question 36

What is the theoretical oxygen demand for oxidising 1 g of ammonia nitrogen to nitrate?

  1. About 0.5 g O₂
  2. About 1 g O₂
  3. About 4.57 g O₂
  4. About 10 g O₂
Show answer & solution

Answer: (C) About 4.57 g O₂

NH₄⁺ + 2O₂ → NO₃⁻ + 2H⁺ + H₂O.

Question 37

What is the BOD rate equation commonly assumed?

  1. Independent of time
  2. Second-order
  3. Zero-order
  4. First-order: BODt = L₀(1 − e^(−kt))
Show answer & solution

Answer: (D) First-order: BODt = L₀(1 − e^(−kt))

L₀ is the ultimate BOD.

Question 38

What is the ultimate BOD if BOD₅ is 200 mg/L and k = 0.23 per day (base e)?

  1. About 146 mg/L
  2. About 200 mg/L
  3. About 293 mg/L
  4. About 1,000 mg/L
Show answer & solution

Answer: (C) About 293 mg/L

L₀ = 200/(1 − e^(−1.15)) = 200/0.683.

Question 39

What is the effect of temperature on BOD reaction rate?

  1. It decreases with temperature
  2. It increases with temperature, often corrected with θ ≈ 1.047
  3. It doubles every degree
  4. No effect
Show answer & solution

Answer: (B) It increases with temperature, often corrected with θ ≈ 1.047

kT = k20 θ^(T−20).

Question 40

What does the oxygen sag curve describe?

  1. Dissolved oxygen in a river downstream of a waste discharge, falling then recovering
  2. Ozone levels
  3. BOD in sludge
  4. Oxygen in air
Show answer & solution

Answer: (A) Dissolved oxygen in a river downstream of a waste discharge, falling then recovering

The Streeter–Phelps equation models it.

Question 41

What is the critical point on the oxygen sag curve?

  1. The point of minimum dissolved oxygen downstream of the discharge
  2. The point of maximum DO
  3. The source of the river
  4. The discharge point
Show answer & solution

Answer: (A) The point of minimum dissolved oxygen downstream of the discharge

Its value determines whether aquatic life survives.

Question 42

What is sludge dewatering?

  1. Aerating sludge
  2. Reducing water content of sludge using belt presses, centrifuges, filter presses or drying beds
  3. Adding water to sludge
  4. Disinfecting sludge
Show answer & solution

Answer: (B) Reducing water content of sludge using belt presses, centrifuges, filter presses or drying beds

Dewatered cake is easier to transport.

Question 43

What is the main source of the high BOD in sugar mill effluent?

  1. Radioactivity
  2. Heavy metals
  3. Salt
  4. Sugar losses and wash water containing organic matter
Show answer & solution

Answer: (D) Sugar losses and wash water containing organic matter

Mills often use ponds or anaerobic treatment.

Question 44

What is the purpose of an equalisation tank in industrial effluent treatment?

  1. Disinfecting effluent
  2. Removing grit
  3. Smoothing variations in flow and pollutant load before treatment
  4. Producing biogas
Show answer & solution

Answer: (C) Smoothing variations in flow and pollutant load before treatment

It improves stability of biological processes.

Question 45

Why is chromium reduced from Cr(VI) to Cr(III) in effluent treatment?

  1. Cr(III) is more toxic
  2. Cr(III) is far less toxic and can be precipitated as hydroxide
  3. To produce colour
  4. Cr(VI) precipitates better
Show answer & solution

Answer: (B) Cr(III) is far less toxic and can be precipitated as hydroxide

Reducing agents such as sodium metabisulphite are used.

Question 46

What is reverse osmosis used for in effluent treatment?

  1. Recovering high-quality water from treated effluent for reuse
  2. Primary sedimentation
  3. Removing grit
  4. Producing biogas
Show answer & solution

Answer: (A) Recovering high-quality water from treated effluent for reuse

Reject brine requires careful disposal.

Practice these 46 questions interactively →