What is the strike of a bed?
Show answer & solution
Answer: (B) The direction of a horizontal line on the bedding plane
Strike is at right angles to the dip direction.
Mining Engineering · Mining Geology & Pakistan Minerals
36 questions, each with the answer and a worked solution.
Practice interactively and track your score →What is the strike of a bed?
Answer: (B) The direction of a horizontal line on the bedding plane
Strike is at right angles to the dip direction.
What is an anticline?
Answer: (B) An upfold in which the oldest rocks are in the core
Anticlines are important traps for oil and gas.
What is a syncline?
Answer: (C) A downfold in which the youngest rocks are in the core
Coal basins often occupy synclines.
What is the plunge of a fold?
Answer: (A) The inclination of the fold axis from the horizontal
Plunging folds give curved outcrop patterns.
What is an overturned fold?
Answer: (D) A fold in which one limb has been tilted beyond vertical
In overturned limbs the beds are upside down.
What is a recumbent fold?
Answer: (B) A fold whose axial plane is nearly horizontal
Recumbent folds form under intense compression.
What is a normal fault?
Answer: (C) A fault in which the hanging wall has moved down relative to the footwall
Normal faults form under tension.
What is a reverse fault?
Answer: (A) A fault in which the hanging wall has moved up relative to the footwall
Reverse faults form under compression.
What is a thrust fault?
Answer: (D) A low-angle reverse fault
Thrusts can push older rocks over younger rocks.
What is a strike-slip fault?
Answer: (D) A fault in which movement is mainly horizontal, parallel to the strike
The Chaman Fault is a major strike-slip fault.
Which major strike-slip fault runs through western Balochistan along the Pakistan–Afghanistan border region?
Answer: (C) Chaman Fault
The Chaman Fault is a left-lateral transform fault zone.
What is a horst?
Answer: (A) An uplifted block between two normal faults
A graben is the opposite: a down-dropped block.
What is a graben?
Answer: (B) A down-dropped block between two normal faults
Grabens form rift valleys.
What is the throw of a fault?
Answer: (A) The vertical displacement of a bed across the fault
Throw determines how far a seam must be followed after a fault.
What is the heave of a fault?
Answer: (D) The horizontal displacement of a bed across the fault
Heave is measured at right angles to strike.
What is fault gouge?
Answer: (C) Fine clay-like crushed rock along a fault plane
Gouge is weak and may carry water.
What is fault breccia?
Answer: (B) Angular broken rock fragments in a fault zone
Breccia forms by crushing during faulting.
What are slickensides?
Answer: (C) Polished, grooved surfaces on a fault plane showing the direction of movement
Slickensides help determine fault movement direction.
What is a joint in rock?
Answer: (D) A fracture along which there has been no appreciable displacement
Joints control blasting, slope stability and water flow.
What is an unconformity?
Answer: (A) A buried erosion surface representing a gap in the geological record
Unconformities separate rocks of very different ages.
What is a dyke?
Answer: (B) A tabular igneous intrusion that cuts across the bedding
Dykes are discordant intrusions.
What is a sill?
Answer: (B) A tabular igneous intrusion parallel to the bedding
Sills are concordant intrusions.
What does the law of superposition state?
Answer: (D) In undisturbed sedimentary rocks, younger beds lie above older beds
It is a basic principle of stratigraphy.
What is a washout in a coal seam?
Answer: (C) A channel where the coal has been eroded and replaced by sandstone or other sediment
Washouts reduce reserves and disrupt mining.
What is a seam split?
Answer: (A) A place where a coal seam divides into two or more seams separated by rock
Splits change mining height and quality.
What is foliation in metamorphic rocks?
Answer: (D) A planar arrangement of minerals produced by pressure
Schist and gneiss show strong foliation.
What is the outcrop of a bed?
Answer: (C) The area where the bed appears at the ground surface
Outcrop patterns are used in geological mapping.
Which major thrust separates the Himalayan foothills from the Potwar plateau region in northern Pakistan?
Answer: (B) Main Boundary Thrust
The MBT is a major active thrust of the Himalayan system.
What is the dip of a bed?
Answer: (A) The maximum angle of inclination of the bed below the horizontal
Dip is measured at right angles to strike.
What is an isoclinal fold?
Answer: (D) A fold in which both limbs are parallel
Isoclinal folds form under intense deformation.
Why are faults important in underground mining?
Answer: (B) They displace seams and orebodies and may bring weak ground, water and gas
Faults require changes in mine layout and support.
What is the axial plane of a fold?
Answer: (A) The plane that divides the fold as symmetrically as possible through the hinges
The attitude of the axial plane classifies folds as upright, inclined or recumbent.
What is the hinge of a fold?
Answer: (D) The line of maximum curvature of the folded bed
Hinges join to form the fold axis.
What is a nonconformity?
Answer: (C) An erosion surface where sedimentary rocks lie on igneous or metamorphic rocks
It represents a long period of uplift and erosion.
What is an angular unconformity?
Answer: (D) An erosion surface where younger beds lie at an angle on tilted older beds
It shows folding or tilting before erosion and later deposition.
What is a drag fold next to a fault?
Answer: (A) Bending of beds next to a fault caused by fault movement
Drag folds can indicate the sense of movement.