Engineering, Management, Agriculture and Veterinary MCQs are now live. FPSC, PPSC, EPE, IELTS & GRE coming soon.

Metrology & Measurement: Metrology and Bench Work

Mechanical Engineering · Metrology & Measurement

33 questions, each with the answer and a worked solution.

Practice interactively and track your score →
Question 1

What is the least count of a typical metric vernier caliper?

  1. 0.001 mm
  2. 0.02 mm
  3. 0.1 mm
  4. 1 mm
Show answer & solution

Answer: (B) 0.02 mm

Some vernier calipers have a least count of 0.05 mm.

Question 2

What is the least count of a standard metric micrometer?

  1. 0.01 mm
  2. 0.02 mm
  3. 0.1 mm
  4. 1 mm
Show answer & solution

Answer: (A) 0.01 mm

It has a 0.5 mm pitch screw and 50 thimble divisions.

Question 3

What are slip gauges (gauge blocks) used for?

  1. Measuring surface finish
  2. Measuring angles directly
  3. Cutting metal
  4. Providing accurate reference lengths for setting and calibrating instruments
Show answer & solution

Answer: (D) Providing accurate reference lengths for setting and calibrating instruments

They are wrung together to build up required lengths.

Question 4

What is a sine bar used for?

  1. Measuring diameters
  2. Measuring threads only
  3. Measuring surface roughness
  4. Measuring or setting angles accurately, using slip gauges
Show answer & solution

Answer: (D) Measuring or setting angles accurately, using slip gauges

sin θ = height of slip gauges ÷ length of sine bar.

Question 5

What is a bevel protractor used for?

  1. Measuring angles
  2. Measuring flatness
  3. Measuring lengths
  4. Measuring hole depth
Show answer & solution

Answer: (A) Measuring angles

A vernier bevel protractor reads to 5 minutes.

Question 6

What is a dial indicator used for?

  1. Measuring hardness
  2. Measuring temperature
  3. Measuring small linear displacements and checking run-out and alignment
  4. Measuring angles
Show answer & solution

Answer: (C) Measuring small linear displacements and checking run-out and alignment

It converts small plunger movement into needle rotation.

Question 7

What is a plug gauge used to check?

  1. Thread pitch only
  2. The size of holes
  3. Surface finish
  4. The size of shafts
Show answer & solution

Answer: (B) The size of holes

It has GO and NO-GO ends.

Question 8

What is a snap (gap) gauge used to check?

  1. Angles
  2. Surface finish
  3. The size of shafts and external dimensions
  4. The size of holes
Show answer & solution

Answer: (C) The size of shafts and external dimensions

Ring gauges are also used for shafts.

Question 9

In a limit gauge, what does it mean if the GO end does not enter a hole?

  1. The hole is perfect
  2. The hole is oversize
  3. The gauge is worn only
  4. The hole is undersize and must be rejected or reworked
Show answer & solution

Answer: (D) The hole is undersize and must be rejected or reworked

A good hole accepts the GO end but not the NO-GO end.

Question 10

What does Taylor's principle of gauging state?

  1. The GO gauge should check all features of the part together, while the NO-GO gauge should check one feature at a time
  2. Only one gauge is needed
  3. Gauges should be made of wood
  4. Only NO-GO gauges are needed
Show answer & solution

Answer: (A) The GO gauge should check all features of the part together, while the NO-GO gauge should check one feature at a time

A full-form GO gauge checks both size and form.

Question 11

What is surface roughness (Ra) a measure of?

  1. The colour of a surface
  2. The hardness of a surface
  3. The average deviation of the surface profile from its mean line
  4. The flatness of a surface
Show answer & solution

Answer: (C) The average deviation of the surface profile from its mean line

It is measured in micrometres.

Question 12

What is an optical flat used for?

  1. Measuring angles
  2. Measuring roughness
  3. Measuring diameter
  4. Checking flatness of surfaces using light interference fringes
Show answer & solution

Answer: (D) Checking flatness of surfaces using light interference fringes

Straight, evenly spaced fringes indicate a flat surface.

Question 13

What is a coordinate measuring machine (CMM)?

  1. A machine that measures the geometry of parts by sensing points on their surfaces in three dimensions
  2. A casting machine
  3. A cutting machine
  4. A welding machine
Show answer & solution

Answer: (A) A machine that measures the geometry of parts by sensing points on their surfaces in three dimensions

It is used for inspection of complex parts.

Question 14

What is a comparator?

  1. An instrument that measures absolute length
  2. An instrument that compares a part with a standard and shows the difference in dimension
  3. A gauge block
  4. A cutting tool
Show answer & solution

Answer: (B) An instrument that compares a part with a standard and shows the difference in dimension

Comparators may be mechanical, optical, electrical or pneumatic.

Question 15

What is an autocollimator used for?

  1. Measuring temperature
  2. Measuring small angular deviations and checking straightness and flatness
  3. Measuring hole diameter
  4. Measuring hardness
Show answer & solution

Answer: (B) Measuring small angular deviations and checking straightness and flatness

It uses a reflected light beam.

Question 16

On which stroke does a file remove metal?

  1. The forward stroke
  2. Neither stroke
  3. The return stroke
  4. Both strokes
Show answer & solution

Answer: (A) The forward stroke

Pressure should be released on the return stroke.

Question 17

In which direction should hacksaw blade teeth point?

  1. Towards the handle
  2. Downwards
  3. Forward, away from the handle
  4. Upwards
Show answer & solution

Answer: (C) Forward, away from the handle

The cut is made on the forward stroke.

Question 18

What is the correct order of using a set of hand taps?

  1. Any order
  2. Second, plug and taper
  3. Plug, taper and second
  4. Taper tap, second (intermediate) tap and plug (bottoming) tap
Show answer & solution

Answer: (D) Taper tap, second (intermediate) tap and plug (bottoming) tap

The taper tap starts the thread easily.

Question 19

What tool is used to cut external threads by hand?

  1. Die and die stock
  2. Tap and tap wrench
  3. Scraper
  4. Reamer
Show answer & solution

Answer: (A) Die and die stock

Taps cut internal threads.

Question 20

What is a surface plate used for?

  1. Bending sheets
  2. Providing a flat reference surface for marking out and inspection
  3. Cutting metal
  4. Holding drills
Show answer & solution

Answer: (B) Providing a flat reference surface for marking out and inspection

It is made of cast iron or granite.

Question 21

What is a centre punch used for?

  1. Marking straight lines
  2. Cutting metal
  3. Measuring angles
  4. Making a conical mark to locate the centre of a hole before drilling
Show answer & solution

Answer: (D) Making a conical mark to locate the centre of a hole before drilling

Its point angle is about 90°.

Question 22

What is a scriber used for?

  1. Measuring diameters
  2. Cutting threads
  3. Drawing lines on metal surfaces during marking out
  4. Filing
Show answer & solution

Answer: (C) Drawing lines on metal surfaces during marking out

It has a hardened steel point.

Question 23

What are the common grades of file cut, from coarse to fine?

  1. Flat, round and square
  2. Single, double and triple only
  3. Smooth, bastard, rough
  4. Rough, bastard, second cut, smooth and dead smooth
Show answer & solution

Answer: (D) Rough, bastard, second cut, smooth and dead smooth

The bastard file is used for general roughing.

Question 24

What is a mortise gauge used for in carpentry?

  1. Boring holes
  2. Cutting curves
  3. Marking two parallel lines for mortises using two scribing pins
  4. Planing wood
Show answer & solution

Answer: (C) Marking two parallel lines for mortises using two scribing pins

A marking gauge has only one pin.

Question 25

What is an auger used for in carpentry?

  1. Planing surfaces
  2. Boring holes in wood
  3. Marking lines
  4. Cutting joints
Show answer & solution

Answer: (B) Boring holes in wood

It is a boring tool, not a planing tool.

Question 26

What is a gouge?

  1. A chisel with a curved, hollow-shaped blade
  2. A saw
  3. A planing tool
  4. A flat chisel
Show answer & solution

Answer: (A) A chisel with a curved, hollow-shaped blade

It is used for cutting grooves and curved shapes in wood.

Question 27

What is an anvil used for in smithy work?

  1. Heating the metal
  2. Measuring the metal
  3. Cooling the metal
  4. Supporting work while it is hammered and shaped
Show answer & solution

Answer: (D) Supporting work while it is hammered and shaped

The horn of the anvil is used for bending curves.

Question 28

What is a swage block?

  1. A heavy cast-iron block with holes and grooves used for bending and shaping metal in smithy
  2. A measuring instrument
  3. A cutting tool
  4. A furnace
Show answer & solution

Answer: (A) A heavy cast-iron block with holes and grooves used for bending and shaping metal in smithy

It supports work during forging operations.

Question 29

What is a V-block used for?

  1. Cutting threads
  2. Measuring angles directly
  3. Holding round work for marking out, drilling or inspection
  4. Grinding
Show answer & solution

Answer: (C) Holding round work for marking out, drilling or inspection

V-blocks are usually made in matched pairs.

Question 30

What is a try square used for?

  1. Measuring length accurately to 0.01 mm
  2. Checking and marking right angles
  3. Cutting wood
  4. Boring holes
Show answer & solution

Answer: (B) Checking and marking right angles

It consists of a blade fixed at 90° to a stock.

Question 31

What is the purpose of marking out before machining?

  1. Measuring hardness
  2. Cleaning the work
  3. Hardening the surface
  4. Showing the positions of holes, edges and centres on the workpiece
Show answer & solution

Answer: (D) Showing the positions of holes, edges and centres on the workpiece

Layout dye makes scribed lines easy to see.

Question 32

What is a hacksaw blade with fine teeth (more teeth per inch) used for?

  1. Cutting large solid bars quickly
  2. Cutting thin sections and hard materials
  3. Cutting soft thick wood
  4. Cutting plastic only
Show answer & solution

Answer: (B) Cutting thin sections and hard materials

At least three teeth should be in contact with the work.

Question 33

What is a feeler gauge used for?

  1. Measuring diameters
  2. Measuring small gaps such as valve clearances
  3. Measuring angles
  4. Measuring depth of holes
Show answer & solution

Answer: (B) Measuring small gaps such as valve clearances

It consists of thin steel blades of known thickness.

Practice these 33 questions interactively →